FBSUSB
DSTIKE WiFi Deauther V4S Smart Watch Development Board
DSTIKE WiFi Deauther V4S Smart Watch Development Board
Couldn't load pickup availability
WHAT IS IT?
Deauther watch SE has redesigned surface and circuit. RTC could work for several months after you turn off the watch. You can also flash deauth detector software because it has buzzer now.
Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.
It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.
Please note that the ESP8266 does only support 2.4GHz.
You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.
FUNCTION
Deauther Attack: Disconnect 2.4G WiFi
Deauther Beacon: Create fake networks
Deauther Probe:Confuse wifi trackers
Packet Monitor:Display wifi traffic
GPIOS AND HARDWARE INFO
Display: SH1106 1.3" OLED
Display SDA: GPIO 5
Display SCL/SCK: GPIO 4
WS2812b LED: GPIO 15
Button Up: GPIO 12
Button Down: GPIO 13
Button Select: GPIO 14
Buzzer: GPIO 0
Side Button: RST
WHY DID YOU MAKE IT?
I designed this development board especially for Spacehuhn's great project: ESP8266 Deauther. It has been authorized by him and is officially supported.
Thanks to every customer that leaves feedback! I will keep improving this board.
WHAT MAKES IT SPECIAL?
Double Arcylic Protection
Transparent Case
Soft sillica gel strap
500 mA charging current
Indicate charging LED (RED will turn off when full)
ESP12F Inside
Power Switch
Protection: short, overcharging, over discharging, temperature
DISCLAIMER
This project is a proof of concept for testing and educational purposes. Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!
Use it only against your own networks and devices! Please check the legal regulations in your country before using it. We don't take any responsibility for what you do with this program.
MORE INFO
Deauth
Closes the connection of WiFi devices by sending deauthentication frames to access points and client devices you selected. This is only possible because a lot of devices don't use the 802.11w-2009 standard that offers a protection against this attack. Please only select one target! When you select multiple targets that run on different channels and start the attack, it will quickly switch between those channels and you have no chance to reconnect to the access point that hosts this web interface.
Beacon
Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.
Probe
Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It's unlikely you will see any impact by this attack with your home network.
VIDEOS
Software 2.6.0 Introduction
How to connect smart phone
DSTIKE Deauther Watch Demo
NTP Time server functions
How to install DSTIKE Arduino environment
How to use 8266 flash tool flash deauther firmware
V3S description :
What is it?
Deauther Watch V3S is the updated version of the old V3. With the latest Deauther software, you can perform various attacks to test WiFi networks. Please note that ESP8266 only supports 2.4GHz frequency. Additionally, you can utilize it for developing your own software. It is user-friendly and operates similar to any other ESP8266 development board.
Upgrade Log
WiFi chip upgraded from 1MB ESP07s to 4MB DSTIKE ESP07.
Watch strap upgraded from knitted strap to silicone strap.
Battery upgraded from 800mAh to 1000mAh.
USB upgraded from Micro USB to Type-C.
Indicator LEDs have been removed to eliminate annoyance.
Laser has been removed.
An external SMA connector has been added.
Introducing a new power supply solution that allows for power on/off by pressing for 3 seconds.
Function
Deauther Attack: Disconnect 2.4G WiFi
Deauther Beacon: Create fake networks
Deauther Probe: Confuse WiFi trackers
Packet Monitor: Display WiFi traffic
Clock: Real Time Clock Adjustable
GPIOs and Hardware info
Display: SH1106 1.3" OLED
Display SDA: GPIO 5
Display SCL/SCK: GPIO 4
WS2812b LED: GPIO 15
Button Up: GPIO 12
Button Down: GPIO 13
Button Select: GPIO 14
Bright LED: GPIO 16
Side Button: Power and Reset
Why did you make it?
I designed this development board especially for Spacehuhn's great project: ESP8266 Deauther. It has been authorized by him and is officially supported. Thanks to every customer that leaves feedback! I will keep improving this board.
Package Included
1 x DSTIKE Deauther Watch V3
1 x Typec Power/Data cable
1 x Arcylic Cover board
1 x Software manual
Disclaimer
This project serves as a proof of concept for testing and educational purposes. It is important to note that neither the ESP8266 nor its SDK were intended or developed for such purposes. As a result, bugs may occur. Please ensure that you only use this project against your own networks and devices. Prior to usage, it is essential to review and comply with the legal regulations pertaining to your country. We do not accept any responsibility for any actions taken with this program.
More Info
Deauth
The deauthentication feature is designed to close the connection of WiFi devices by sending deauthentication frames to the selected access points and client devices. It's important to note that this attack is only possible because many devices do not implement the 802.11w-2009 standard, which provides protection against such attacks.
To ensure proper usage, please select only one target at a time. If you select multiple targets running on different channels and initiate the attack, the system will rapidly switch between those channels, making it difficult to reconnect to the access point hosting the web interface.
Beacon
Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.
Probe
Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It's unlikely you will see any impact by this attack with your home network.
Here I post a few quick links:
Software https://github.com/SpacehuhnTech/esp8266_deauther
Hardware https://github.com/lspoplove/Deauther-Project
WiKi https://github.com/SpacehuhnTech/esp8266_deauther/wiki
FAQ https://github.com/SpacehuhnTech/esp8266_deauther/wiki/FAQ
Burning tutorial https://github.com/SpacehuhnTech/esp8266_deauther/wiki/Installation
Burning tool https://github.com/nodemcu/nodemcu-flasher
Firmware download https://github.com/SpacehuhnTech/esp8266_deauther/releases
Please Check out the how-to video link :
https://www.youtube.com/watch?v=TMvpJiE8Yy8
Quick product upgrade tutorial:
1. Download CP2102 driver (https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers)
2. Download the firmware (https://github.com/SpacehuhnTech/esp8266_deauther/releases)
3. Download nodemcu-flasher (https://github.com/nodemcu/nodemcu-flasher)
4. Click the gear to select the corresponding binfile. The programming mode selects DOUT. The rate selects 961200. Click Flash start and wait for the progress bar to reach the end and then power on
Search Deauther on Github to find the corresponding project. On Github, we have put YouTube video links, WiKi, FAQ, etc., which can basically solve 90% of your problems. You can check the issues of this project for the remaining 10%. You can ask questions in the issues, or you can View answers to the same questions asked by others
Deauther Watch is still an ESP8266 development board, but you can wear it like a smart watch.
I provide 3D print case only for Deauther Watch.
But I do not provide case for old Deauther Wristband.
3D Print Case Download:
https://github.com/lspoplove/Deauther-Project/blob/master/3DPrint/DeautherWatch.STL
Assemble Video
https://youtu.be/-aw1laQx-1c
It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.
Please note that the ESP8266 does only support 2.4GHz. For more details on the software, visit here.
https://github.com/spacehuhn/esp8266_deauther
You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.
GPIOs and hardware info
Display SH1106 1.3 OLED
Display SDA GPIO 5 (D1)
Display SCL/SCK GPIO 4 (D2)
WS2812b LED GPIO 15 (D8)
Button Up GPIO 12
Button Down GPIO 13
Button Select GPIO 14
High Light LED GPIO 16
Side Button GPIO0 GPIO2 RST
Please use computer to see more details
Deauther Watch V2 fixed all the problems I collected. Now hardware has RTC but software will update later. ESP32 does not support deauther.
Update Log
DifferenceDeauther WristbandDeauther Watch V1Deauther Watch V2
Battery500mah500mah800mah
3D Print CaseNoYESYES
Screen ProtectionNoNoYES
Battery IndicateNoNoYES
Power SwitchPlasticPlasticMetal
Charging Current0.5A0.5A0.8A
RTC DS3231NoNoYES
Breakout GPIOsNoYESYES
ColorBlack&RedBlack
Black&White
What is it?
Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.
This ESP8266 development board comes with a 800mAh battery, OLED display and a 3-way momentary slide switch.
It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.
Please note that the ESP8266 does only support 2.4GHz. For more details on the software, visit here.
You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.
GPIOs and hardware info
Display: SH1106 1.3" OLED
Display SDA: GPIO 5 (D1)
Display SCL/SCK: GPIO 4 (D2)
WS2812b LED: GPIO 15 (D8)
Button Up: GPIO 12
Button Down: GPIO 13
Button Select: GPIO 14
High Light LED: GPIO 16
Side Button: GPIO0,RST
Why did you make it?
I designed this development board especially for Spacehuhn's great project: ESP8266 Deauther. It has been authorized by him and is officially supported.
Thanks to every customer that leaves feedback! I will keep improving this board.
What makes it special?
Only ~80mA power usage
Up to around 8-10 hours work time
800 mA charging current
Indicate charging LED (25%,50%,75%,100%)
Included 5dB FPC antenna and 2dB antenna
Power Switch (Click to turn on, double click to turn off)
Protection: short, overcharging, over discharging, temperature
Added Extremely Accurate DS3231
Disclaimer
Use it only for testing and educational purposes against your own devices! I don't take responsibility for what you do with it.
Please check the legal regulations for your country to make sure you don't violate any laws.
You can get full information from WiKi
Assemble Video
Scehmatic and 3D Print Design files
RTC Test
What is it?
I call it D&B watch. It is a Deauther & Bad USB watch. You can also call it deauther watch V4. You can look Deauther Watch V3 to understand what is deauther.
Why did you make it?
In order to make it more fun. I added atmega32u4(Arduino Leonardo) to this watch. Now this watch not only disconnect wifi but also perform bad usb attack!
What makes it special?
Compare to deauther watch V3:
ESP07 changed to ESP07s: With an external 3dB antenna it could search more signal than V3. You can also add bigger antenna to the SMA connector.
Added Atmega32u4: I flashed Arduino Leonardo bootloader already. You can program it as bad usb directly.Two buttons(Digital pin 9 and 10) could be used to execute different commands. I flashed a demo program. When bad usb port connects PC, press DP9 button cmd window will be opened. Press DP10 button Notepad will be opened. You can reprogram it via Arduino IDE.
Bridge: There are empty solder pads at the back of this watch. You can solder them to connect ESP8266 with atmega32u4. For example if you solder IIC pads this watch could become wifi duck.
Battery: 800mAh battery upgrade to 1000mAh. There are more space inside to put bigger battery instead.
Strap: Canvas strap upgrade to silicone strap.
Design: 3D case has been redesigned. Added bottom arcylic board to pretect this watch.
Charging: There are two usbs. Each usb could be used to charge battery. But I do not suggest you use them at the same time.
Deauther Watch SE
